Selamat Datang ke Portal Rasmi Jabatan Standard Malaysia

1 JULY 2024 – 30 AUGUST 2024

No.

Title of DMS

Scope

Link

NSC 03 – CONSUMER INTEREST

1.

DMS 2754-2

Sharing economy – Part 2: General trustworthiness and safety requirements for digital platforms

This Malaysian Standard specifies general trustworthiness and safety requirements as well as provide guideline for platform operator when verifying providers, including on-boarding, maintenance and deactivation.

This document applies to both digital platform operators and providers within the sharing economy. While this document does not cover system requirements for digital platforms, the document is still beneficial for system development.

VIEW

NSC 18 – MEDICAL DEVICES AND FACILITIES FOR HEALTHCARE

1.

DMS IEC 60364-7-710:2021 – Low-voltage electrical installations – Part 7-710: Requirements for special installations or locations - Medical locations   (IEC 60364-7-710:2021, IDT) (Published by Department of Standards Malaysia in 2024)

This particular requirements of this part of IEC 60364 apply to electrical installations in medical locations so as provide safety of patients and medical staff. These requirements refer to:

-       hospitals and clinics or equivalent institutions (including equipment transportable and mobile locations);

Which, subject to assessment (710.30), can also include:

-       sanatoriums and health clinics;

-       dedicated locations in homes for senior citizens and aged care homes, where patients receive medical care;

-       medical centres, outpatients’ clinics and departments, casualty wards;

-       other outpatients’ institutions (industrial, sports and others);

-       medical and dental practices;

-       dedicated medical rooms in the workplace;

-       veterinary clinics;

-       rooms in existing installations where a change of utilization for medical applications occur.

This list is not exhaustive.

The requirements of this document do not apply to medical electrical (ME) equipment or ME systems.

VIEW

15 JULY 2024 – 14 SEPTEMBER 2024

No.

Title of DMS

Scope

Link

NSC 17 – TEXTILES AND APPARELS

1.

DMS 1747-1 Tenunan Malaysia – Bahagian 1: Songket Malaysia - Spesifikasi

(Semakan ketiga)

Standard Malaysia ini menetapkan spesifikasi bahan mentah yang digunakan dalam proses tenunan, kriteria kualiti, proses penghasilan, struktur asas, kaedah penjagaan, kaedah ujian, penandaan dan pelabelan bagi Songket Malaysia.

VIEW

NSC 25 – QUALITY AND ORGANISATIONAL MANAGEMENT

1.

DMS ISO/FDIS 56001 Innovation management system - Requirements

This document specifies requirements for establishing, implementing, maintaining, and improving an innovation management system when an organization:

a) needs to develop and demonstrate its capability to effectively manage innovation activities to achieve sustained success;

b) aims to enhance its innovation performance through the realization of value for users, customers, and other interested parties.

All the requirements of this document are generic and are intended to be applicable to any organization, including all functions, regardless of its type or size, the products and services it provides, or types of innovations and innovation approaches used.

The document can be used by:

a) organizations aiming to systematically manage their innovation activities to achieve intended results;

b) users, customers, and other interested parties seeking confidence in the innovation capabilities of an organization;

c) policy makers aiming to foster innovation activities and support sustainable development.

VIEW

UNDER DEVELOPMENT

1 AUGUST 2024 – 30 SEPTEMBER 2024

No.

Title of DMS

Scope

Link

NSC 02 – CHEMICALS AND MATERIALS

1

DMS 132: 2024, Undercoating Paint for Gloss Enamel – Specification (Second Revision)

This Malaysian Standard specifies requirements for an undercoating paint for use on primed interior and exterior metal and wood surfaces under gloss enamel paint or its equivalent.

VIEW

2

DMS 134: 2024, Emulsion paint for exterior and interior use – Specification (Fourth revision)

This Malaysian Standard specifies an air-drying emulsion paint including textured finish suitable for exterior and interior use on masonry surfaces including concrete, brick, stucco, concrete block and fibre cement roofing and sidings, and for recoating of previously painted surface provided the surface is in sound condition and suitable for receiving such a coating. It may also be used on suitably primed metal and wood surfaces.

NOTE. Paints specifically for interior use only are covered by MS 903, Specification for latex emulsion paint for interior use.

VIEW

3

DMS 164: 2024, Road marking paints – Specification (Fourth revision)

This Malaysian Standard specifies requirements for road marking paints for use on bituminous traffic bearing surfaces.

VIEW

NSC 04 – BUILDING, CONSTRUCTION AND CIVIL ENGINEERING

1

DMS 2753-1:2024 Use of glass in building - Code of Practice: Part 1 - Selection of glass

The Code of Practice - Use of glass in buildings, provides guidelines on the design, construction, testing, quality assurance and installation of glass structures or elements in buildings.

1.1       Design considerations

a)         Aim of glass design

In the Code, the limit state design principle is adopted for structures using glass with the aim to achieve the following:

i)          Overall stability and buckling resistance against the design loads;

ii)         Strength against collapse under the design loads and the imposed deformations of supporting structures;

iii)        Integrity and robustness against progressive collapse under the design loads;

iv)        Serviceability under the design loads and the imposed deformations of supporting structures;

v)         Water and air tightness;

vi)        Durability;

vii)       Quality; and

viii)      Maintainability during its design working life.

b)         Design references

The Code has made references to various international standards in Annex A. Where an alternative method or a performance-based approach is adopted, adequate information, including proposals on compliance testing, must be provided to demonstrate that the aim of glass design specified in clause 1.1 a) can be achieved.

VIEW

2

DMS 2753-2:2024 Use of glass in building - Code of Practice: Part 2 - Design and analysis

The Use of glass in buildings - Code of Practice - Part 2: Design and analysis, provides guidelines on the design, construction, testing, quality assurance and installation of glass structures or elements in buildings.

1.1 Design considerations

a) Aim of glass design

In the Code, the limit state design principle is adopted for structures using glass with the aim to achieve the following:

i)          Overall stability and buckling resistance against the design loads;

ii)         Strength against collapse under the design loads and the imposed deformations of supporting structures;

iii)        Integrity and robustness against progressive collapse under the design loads;

iv)        Serviceability under the design loads and the imposed deformations of supporting structures;

v)         Water and air tightness;

vi)        Durability;

vii)       Quality; and

viii)      Maintainability during its design working life.

b) Design references

Where an alternative method or a performance-based approach is adopted, adequate information, including proposals on compliance testing, must be provided to demonstrate that the aim of glass design specified in clause 1.1a can be achieved.

VIEW

15 AUGUST 2024 – 14 OCTOBER 2024

No.

Title of DMS

Scope

Link

NSC 05- NATIONAL STANDARDS COMMITTEE ON GENERATION, TRANSMISSION AND DISTRIBUTION OF ENERGY

1

DMS IEC 62641:2022 Conductors for overhead lines –

Aluminium and

aluminium alloy wires for concentric lay

stranded conductors

(IEC 62641:2022, IDT)

This document specifies the mechanical and electrical properties of round

and formed wires for equivalent diameters up to the values according to

Table 3 for aluminium and aluminium alloys and according to Table 4 for

thermal resistant alloys. This document is applicable to aluminium and

aluminium alloy wires for the manufacture of concentric lay overhead

electrical stranded conductors with or without gap(s) for power

transmission purposes.

The various materials and their designations are listed in Table 1. For

calculation purposes, the values listed in Table 1 are used.

VIEW

NSC 19- NATIONAL STANDARDS COMMITTEE ON ELECTRICAL AND ELECTRONICS EQUIPMENTS AND ACCESSORIES

1

DMS EN 12464-

1:2021

Light and lighting -

Lighting of work

places Part 1: Indoor work places

(EN 12464-1:2021)

This document specifies lighting requirements for humans in indoor work

places, which meet the needs for visual comfort and performance of

people having normal, or corrected to normal ophthalmic (visual) capacity.

All usual visual tasks are considered, including Display Screen Equipment

(DSE).

This document specifies requirements for lighting solutions for most indoor

work places and their associated areas in terms of quantity and quality of

illumination. In addition, recommendations are given for good lighting

practice including visual and non-visual (non-image forming) lighting needs.

This document does not specify lighting requirements with respect to the

safety and health of people at work and has not been prepared in the field

of application of Article 169 of Treaty on the Functioning of the European

Union although the lighting requirements, as specified in this document,

usually fulfil safety needs.

This document neither provides specific solutions, nor restricts the

designers’ freedom from exploring new techniques nor restricts the use of innovative equipment. The illumination can be provided by daylight,

electric lighting or a combination of both.

This document is not applicable for the lighting of outdoor work places and

underground mining or emergency lighting.

VIEW

2

DMS 60598-2-22:2021

Luminaires – Part 2-22: Particular

requirements –

Luminaires for

emergency lighting

(Second Revision)

 (IEC 60598-2-

22:2021, MOD)

This part of IEC 60598 specifies requirements for emergency luminaires for use with electrical lamps on emergency power supplies not exceeding 1 000 V.

This document does not cover the effects of non-emergency voltage reductions on luminaires incorporating high pressure discharge lamps.

This document gives general requirements for emergency lighting equipment. In this document, the term “lamp” which also includes “light source(s)” where appropriate, is used.

VIEW

NSC 20 – TOURISM AND CULTURE

1

DMS 2765-1 Business events - Part 1:

Convention, exhibition

centre and event space

– General

Requirements

This Malaysian Standard specifies the general requirements of the convention centre, exhibition centre and event space, outlining the general requirements for these spaces encompassing the physical setting, technology and services. This standard serves as a guideline for business events stakeholders, entrepreneurs, relevant authoritative bodies, and interested parties engaged in the business events industry.

VIEW

2

DMS 2765-2 Business Events - Part 2:

Professional Congress

Organiser (PCO) –

Requirements

This Malaysian Standard specifies general criteria and set of requirements for the

standard of PCO classification using the ‘tier-rating’ system. This standard is

intended to be used by relevant authoritative body as well as interested parties that

are engaged in the business events industry to determine the ‘tier-rating’ for PCO.

VIEW

3

DMS 2765-3 Business Events - Part 3:

Professional Exhibition

Organiser (PEO) –

Requirements

This Malaysian Standard describes the requirements of PEO by outlining the role of exhibition organisers encompasses identifying potential business, researching, writing, planning, and running all aspects of exhibitions on behalf of a client (managing) or own organisation (show owners). Exhibition organisers are responsible for overseeing all aspects of an exhibition. This role involves planning, preparation and a customer-focused attitude.

VIEW